CHANTER REED GUIDE
BLOWING-IN NEW REEDS

MAINTENANCE

CHANTER REED PARTS

ADJUSTMENTS
EFFECTS CAUSED BY ADJUSTMENTS OR CONDITIONS

BLOWING-IN NEW REEDS
  • The term "blowing-in" refers to the practice of giving new reeds a chance to settle to their natural strength with minimal adjustment to the reed itself. This is done through simply playing the reed, sometimes with drones plugged to make it more managable. In a reed's early stages, this is necessary due to the fact that new cane will weaken with regular playing, making the reed easier over time. As a general rule, a reed that is immediately comfortable will have a limited lifespan.
  • It is normal for a reed to dry out to some degree during transit or when in storage, so breathe some moist air through the reed for 30 seconds to a minute before trying.
  • If you have a number of reeds to choose from, try to select one slightly above your normal strength. As stated, new reeds will generally become easier with regular playing. How regular will depend on the cane, but as a guide, 30 minutes a day for one week should be enough to bring the reed to a comfortable strength.
  • Don't rely exclusively on the blowing-in process. If a reed is still too firm after a week or so, you may need to coax it to your required strength. This could involve reducing the mouth of the reed and or thinning the blades. These techniques are detailed in Adjustments.
  • If you find that a new reed is so hard to the point of being unplayable, or a reed's strength is suitable but there are other issues relating to pitch or balance, again, the Adjustments section should help.

MAINTENANCE

These points apply to any reed, old or new.

  • Avoid exposing the reed to extreme conditions - too wet, too dry, too hot.
  • Don't lick or soak the reed.
  • Take care not to damage the corners or tips of the reed when handling.
  • To maximise the life of a reed, consider the use of a reed protector. This will enable you to remove the chanter and reed from the bag after playing, which will in turn prevent the reed from absorbing excessive moisture from the bag. If there is moisture surrounding the reed seat after playing, wipe it away and allow the reed to briefly air before putting the protector on.
  • If mould becomes a problem, then you are not drying enough, or you may need to place a small hole (about 1.5 mm) in the protector to allow some evaporation. This can be covered during hotter months if the reed becomes too dry.

CHANTER REED PARTS




ADJUSTMENTS

The following contains information that will assist in getting the best out of new and old reeds. There are really only 4 basic things that can be done directly to a reed: Reduce the mouth, enlarge the mouth, thin the blades, or shorten the blades. These are outlined in detail throughout the first two sections relating to hard and easy reeds. The remaining sections will refer back to these techniques.

REED IS TOO HARD

This advice relates to new reeds that are strong to the point of being unplayable. The following will help you to adjust such reeds to a manageable strength. It will also assist with those reeds that refuse to weaken irrespective of how much they have been played.

There are two basic methods of easing a reed:

1) Reduce the mouth, or opening (the distance between the blades).

2) Thin the blades.

Usually a combination of the two will achieve the best result. If you rely solely on one method, you may compromise the quality and lifespan of the reed. For example, if you make the reed's mouth too small, you could reduce the reed's vibrancy and make it too sharp. If the blades are over-thinned, you could be left with a reed that is unstable and too easy. It is important to understand these points before you proceed.

Before deciding which method to start with, you need to ascertain if the reed is at the correct pitch. If the reed is too hard and also flat, reducing the mouth will help to solve both problems by lifting the pitch and easing the reed.

However, if the reed is correctly pitched, but is still too hard, reducing the mouth could make it too sharp. In this case, the better option would be to thin the blades.


Reduce The Mouth
  • If a reed is only slightly too hard, open and close the reed's mouth a number of times by lightly squeezing the middle and top areas. This will not have a significant affect on pitch, but will help to ease off the reed.
  • If the reed is still too hard and also too flat, particularly C or F, a moderate squeeze at the sound box will assist. Try not to be too aggressive here, as you don't want to risk collapsing the mouth. Generally you only want to squeeze to the point where the tips of the mouth just meet and no further.
  • After a short rest, some new reeds will go flat quickly. This is a symptom of new cane absorbing moisture which causes the mouth of the reed to open up, hence lowering the pitch. In this case, it may be necessary to give the reed a light squeeze to compensate. Once the reed has settled, this should be less necessary.
  • It is important not to rely on only sqeezing a reed to achieve a desired strength. If the reed's mouth becomes too small, volume and harmonics will suffer, and there will be a higher chance of skirling.
  • If the reed's strength is still too hard and yet the pitch is correct or too high, thinning the blades would now be the better option.
Thin The Blades
  • Thinning blades is best done with a sharp hobby knife. The key word here is moderation as once cane is removed, it obviously can't be replaced. The aim is to remove a very small amount of cane and then test. Repeat this process until the reed is at the required strength. It is important not to drastically alter the side-on profile of the reed.
  • Begin by lightly scraping the overall blades in the direction of the grain, taking care not to overdo the centre of the middle and top areas. You should be aiming to remove what looks like powder, rather than go too aggressively. The green zones in the reed image above show the general areas to concentrate initial scraping. Test the reed regularly to avoid going too far.
  • It is important not to over-thin any particular point of the blades. As you proceed, regularly check that they are evenly matched for strength by lightly squeezing the reed towards the middle and look for areas that resist more than others. If this happens and the reed is still too hard, focus your attention on these areas of the blades.
REED IS TOO EASY

Enlarge The Mouth

  • Doing this will increase the reed's strength and lower the pitch. Wet your fingers with tap water and apply some moisture to the sound box. Squeeze the reed at its sides around the sound box area.
  • For a more permanent result, take a reed mandrel and lightly push it into the staple from the reed seat binding end. This should slightly open up the compressed end of the staple and therefore increase the distance between the two blades. Be aware that a little makes a big difference here.
Shorten The Reed
  • Shortening a reed will increase its strength and lift its pitch - be aware of this before proceeding. While there is an amount of risk involved, shortening an old or problematic reed is often successful and is a skill well worth mastering.
  • Holding the reed at the sound box, with the middle and top areas resting on a hard flat surface, cut a small amount of cane (.25 mm to .5 mm) from the tips using a sharp hobby knife or better again a sharp chisel. Depending on how far you have gone, you may need to thin the blades in order to compensate for the increase in strength - just don't end up back where you started. You may also find that the top notes are tight and restricted, in which case thin the overall blades, as above. Also check that the interior of the tips are clean and free from stray cane fibres resulting from the cut.
PITCH IS TOO LOW
  • Remedy by pushing the reed further into the reed seat. Don't go too far as this may cause instability on F and possibly an excessive crow on High A. Be aware that sinking the reed will also sharpen the higher notes more than it will the lower notes. In either direction, the higher notes will be more affected than the lower notes when a reed is repositioned.
  • If the reed is too hard, reducing the reed's mouth will help both issues.
  • If the pitch is too low, but at the required strength, shortening the reed is the only option.
PITCH IS TOO HIGH
  • Reposition the reed higher in the reed seat. This will also flatten the higher notes more than it will the lower notes.
  • The reed may be too dry - adjust your moisture control system if applicable.
  • If the reed is too easy, try opening up the reed's mouth.
SCALE HAS SHARP HIGH NOTES & FLAT LOW NOTES
  • Lifting the reed will help to restore balance, however this will also lower your overall pitch.
  • If the reed is too hard, try thinning the middle area of each blade, fucusing more on the green areas, as per the image above. Ensure that the blades have the same amount of give and that the reed is vibrating efficiently.
  • Thinning the sound box will also help to free up the top hand, but going too far here could compromise stability.
  • Opening the reed's mouth will also help, but also increase strength and lower the pitch. If necessary, thin the blades to compensate.
SCALE HAS FLAT HIGH NOTES & SHARP LOW NOTES
  • Sink the reed, however this will also raise your overall pitch.
  • If the reed is too hard, and you can afford to raise the overall pitch, try reducing the mouth of the reed.
SHARP HIGH G
  • If the reed is too hard, try thinning the middle area of each blade, fucusing more on the green areas, as per the image above. Ensure that the blades have the same amount of give and that the reed is vibrating efficiently.
  • Thinning the sound box will also flatten High G, but going too far here could compromise stability.
  • Opening the reed's mouth will also help, but also increase strength and lower the pitch. If necessary, thin the blades to compensate.
CROW ON HIGH A
  • Excessive High A crow is usually caused by under-blowing the reed. It is quite common in lower grade bands for pipers to blow a reed so that it just vibrates and no more. Increasing air pressure will help to clear the High A, but make sure the reed is firm enough to avoid the chance of skirling on Low A or Low G.
  • This can also caused by the reed sitting too far into the reed seat. Try lifting the reed, bearing in mind you will lower your overall pitch.
  • Check that your reed is not receiving too much moisture. If necessary, adjust your bag set-up to compensate.
  • Sanding the tips of the reed may also help. The simplest method is to sand the outside edge of the tips at 45 degrees on very fine sandpaper - 600 grit to be safe.
  • Another method is to sand directly across the end grain of the tips at 90 degrees. This is a more refined method of shortening a reed, but in very small amounts so the pitch is not that greatly affected. The initial step is to place very fine sandpaper (600 grit) on a flat surface. Then, pinching the blades together at the top area, between forefinger and thumb, pull the reed across the sandpaper for about 2cm. Test the reed and if necessary, repeat the process until the High A is clear. An important step is to check that the outside and particularly the inside of the tips are clean. If necessary, remove any stray cane fibers with the corner of the same sandpaper.
  • It should be noted that some chanters are more susceptible to High A crow than others.
DOUBLE-TONING OR UNSTABLE F
  • Often caused by the reed sitting too far into the reed seat - try lifting the reed.
  • Also caused by the reed's mouth being too open, possibly from excessive moisture. If you can afford to ease the reed and lift the pitch, try reducing the reed's mouth.
  • Another possible cause is that the reed is too long for the chanter. If you can afford to lift your pitch, try shortening the reed.
FLAT F & OR C
  • Usually caused by the reed's mouth being too large. If the reed is too hard, try reducing the mouth.
  • Similar to an unstable F, shortening the reed can also help.
REED SOUNDS DULL
  • Before trying anything else, inspect the inside of the blades by looking down the mouth of the reed. Check for any foreign matter or stray cane fibers. Loose cane fibers shouldn't be there in a new reed, but if the tips have been sanded or cut, it's possible they were not cleaned up thoroughly.
  • If the reed is too easy and you can afford to lower the pitch - open up the mouth of the reed.
  • If the reed is too easy and you can afford to raise the pitch - shorten the reed.
  • If the reed is hard and dull, then the top area of the blades may be too thick. Try thinning the top area right to the edge of the tips, ensuring the blades are still of equal strength. Use a sharp hobby knife, scraping in the direction of the grain, being careful not to damage the end grain of the tips.
  • Excessively dry reeds can sound dull - check your moisture control system if applicable.
  • If none of the above helps, try refreshing the inside of each blade. This is useful for older reeds. With a pipe cleaner dipped in methylated spirits, pull the cleaner through the reed from the reed seat end, moving side to side. Another method is to use the corner of very fine (600 grit) wet and dry sandpaper. Insert it into the mouth just short of the corners, then, lightly pinch the top part of the blades together and pull the sandpaper out. Flip over and repeat for the inside of the other blade. The aim is to remove the smallest amount of cane just to clean up the surface of the reed interior.
"SKIRLING"
  • Usually caused by over-blowing a reed that is too easy, or playing a reed that requires too much tape on High G. Try opening up the reed's mouth with a mandrel to compensate.
  • It can also be caused by not covering the High A or High G holes accurately when finishing a grace note or melody note on either of those holes.
  • Another common error is for the High A thumb to strike the chanter after the other top hand fingers when changing from High A to Low A, or High A to Low G. In this situation, your chances of skirling are greatly increased, particularly if you are playing an easy reed. The top hand fingers and thumb should strike the chanter at the same time when changing on these notes.
"GURGLING" E, LOW A OR LOW G
  • Caused by over-blowing a reed that is too easy.
  • It should be noted that some chanters are more susceptible to this than others.
REED IS UNSTABLE (SENSITIVE TO CLIMATE OR BLOWING)
  • Usually caused by the reed being too easy - it may be at the end of its life.
  • Also caused by too much cane being removed from the sound box or middle area. Try shortening the reed to compensate.
  • Lifting the reed will help to a minor degree with blowing issues, but of course will lower your overall pitch.

EFFECTS CAUSED BY ADJUSTMENTS OR CONDITIONS

REDUCE THE REED'S MOUTH
  • Make the reed easier.
  • Raise the overall pitch, in particular C and F.
  • Help to stabilise a double-toning or unsteady F.
ENLARGE THE REED'S MOUTH
  • Make the reed harder.
  • Lower the overall pitch, in particular C and F.
SINKING THE REED
  • Raise the overall pitch, in particular the higher notes.
  • Possibly cause the High A to take on a crow.
  • Possibly cause a double-toning or unsteady F.
  • Generally make the top notes unsteady if the reed is pushed in too far.
LIFTING THE REED
  • Lower the overall pitch, in particular the top notes.
  • Help to clear up a crowing High A.
  • Help to stabilise a double-toning or unsteady F and the top notes in general.
THINNING THE BLADES
  • Make the reed easier.
  • Lower the pitch of the top notes relative to the lower notes.
  • Possibly brighten tone.
OVER-THINNING THE BLADES
  • Cause the reed's pitch to be overly sensitive to blowing and temperature variation.
  • Make the F unstable and possibly double-tone.
  • Possibly cause a crow on High A.
SHORTENING THE REED
  • Make the reed harder.
  • Raise the overall pitch.
  • Stabilise a double-toning or unsteady F.
SANDING ACROSS THE TIPS
  • Help to clear a crow on High A.
TOO MUCH MOISTURE
  • Cause the reed's mouth to open up.
  • Lower the overall pitch.
  • Possibly cause a double-toning or unstable F.
  • Possibly cause a crow on High A.
NOT ENOUGH MOISTURE
  • Cause the reed to close up.
  • Raise the overall pitch, in particular C, F and High G.
  • Cause the sound quality to become thin and dull.

Ross Bates
0411 168 146

rabates1@live.com

ABN: 24 591 526 576

Website created and maintained by Ross Bates

Last updated 11/11/2026

Copyright © 2005 - 2026 Ross Bates