SYNTHETIC BAG SYSTEMS
CHANTER

DRONES

DRONE JOINTS

CHANTER REED

DRONE REEDS

BALANCING DRONE REEDS


SYNTHETIC BAG SYSTEMS

BAG

  • Regularly check the bag for air-tightness, plugging the 4 stocks with rubber bungs or corks and blow the bag up as tightly as posssible. When testing the bag, move the stocks around as they can seal in one position and leak in another. Also check under the blowpipe stock for pinholes and around the zip if one is fitted. Few bags are absolutely 100% air-tight, so a small amount of air loss should be expected. If you can still blow a very small amount of air into the bag after waiting for 10 seconds, the bag is probably fine.
  • When putting pipes away, always remove the chanter and the blowpipe and leave the zip or back of the bag open. If necessary, use another reed protector for the blowpipe tenon to protect any valve that may be fitted.
  • Also avoid undue pressure on the bag when closing the pipe box.
  • These steps will maximize the lifespan of the bag and hoses.
HOSES
  • If you use hoses inside the bag, regularly check for splitting along their length. Slight kinks in the hoses may not cause an issue, but can avoided by using a deep enough pipe case which will reduce pressure on the hoses.
CHANTER HOSE
  • To allow more moisture to the chanter reed, it has become common practice to remove the chanter hose completely from a drying system. Usually a spit trap or hose will be connected to the blowpipe stock to redirect moist air and saliva away from the chanter reed.
CANISTERS, SILICA BEADS OR CLAY GRANULES (DESICCANT)
  • The granules or beads only require maintenance when moisture is collecting on your reeds, although it is best to dry them on a regular basis to prevent any chance of this happening at all - once a fortnight should be enough for most. Microwave 4 to 5 minutes on medium and then allow to cool (evaporate) before putting them back into the canisters.
  • Pay attention to the chanter canister if you still need to use one. It is best not to have it 100% full as chanter reeds do require some moisture to operate correctly. Whichever canister system you use, ensure that the reed is receiving enough moisture, whether by an air intake or a separator. In addition, avoid drying all of the chanter granules at once, as any sudden change in the amount of moisture passing through to the reed could adversely affect it's pitch and tonal quality. It is best to dry only a quarter of the chanter granules at a time and to then mix them with the others.

CHANTER
  • Clean the inside bore of the chanter by using a soft cotton brush, available from piping suppliers. For the throat and inside the holes, use something like a cotton bud or pipe cleaner.
  • Irrespective of whether a chanter is wooden or plastic, never remove a chanter from its stock by twisting from the bottom - always grab it at the top "bulb", just below the stock ferrule.
  • Ensure tuning tape is in good condition. If the chanter has tape goo stuck to it, remove the tape and clean the chanter down with eucalyptus oil, then dry off, ready for new tape.  If needed, take a photo of the chanter before removing the tape and refer to it for positioning the new tape.

DRONES
  • After playing in cold weather, check the drone bores for condensation. If moisture is present, dry the bores by using a cotton pull-through.
  • Occasionally clean the bores of the drones by using purpose made drone brushes, or again, a cotton pull-through.
  • Oiling drone bores - there are conflicting views as to whether to oil drone bores or not, but a yearly light oil can do no harm. Cold-pressed Almond Oil or Sweet Almond Oil are generally recommended for African Blackwood.
  • Avoid any oil, such as Linseed, which can polymerize, and inhibit the wood's ability to breath.

DRONE JOINTS
  • The most important elements of a drone joint are the quality of the application and that the material used is resistant to moisture. While there are conflicting opinions as to the best type of hemp to use, pre-waxed black hemp is a good choice as it is resistant to moisture and so long as it is applied correctly, will provide a safe and long lasting joint.
  • Irrespective of whether black or yellow hemp is used, wax the first layer with thermowax to prevent the joint slipping. All of the layers should have windings as tight and as close as possible. After each layer has been wound, tie-off the hemp and roll it flat between two pieces of wood. This compresses the hemp before the joint is actually used and will help to prevent further compression in the long-term. 
  • Once the new joint gets to the stage where it is nearly tight but not quite enough, you will probably find that one more complete layer will be too much. At this stage you will have to experiment with a layer of hemp where each winding is spaced by about 2 to 3 millimetres. Doing this will allow you to get the tightness of the joint just right. Remember to roll the joint flat before trying it.
  • It is important not to make a joint too tight, particularly on drones with ivory or imitation ivory ferrules, as they have significantly less blackwood than those with metal ferrules.
  • If needed, lubricate the joint with almond oil or cork wax.

CHANTER REED
  • As much as possible, try to avoid exposing the reed to extreme conditions.
  • Don't lick the reed.
  • Take care not to damage the corners of the reed when handling.
  • To maximise the life of a reed, consider the use of a reed protector. This will enable you to remove the chanter and reed from the bag after playing, which will in turn prevent the reed from absorbing excessive moisture from the bag. If there is moisture surrounding the reed seat after playing, wipe it away and allow the reed to briefly air before putting the protector on.
  • If mould becomes a problem, then you are not drying enough, or you may need to place a small hole (about 1 mm) in the protector to allow some evaporation. This can be covered during hotter months if the reed becomes too dry.

DRONE REEDS
  • Ensure that your drone reeds are clean and free of dirt between the tongue and reed bed. Any foreign matter could well contribute to air leakage and instability.
  • Regularly check that your drones reeds are firmly seated into the drones and that they are straight with no chance of them touching the interior of the stocks.
  • Occasionally check reeds for airtightness. Excessive leaking may suggest dust between the tongue and body or perhaps damage to one or the other.
  • Regularly check that your drone reeds are matched or balanced for stability.

BALANCING DRONE REEDS

As described in the drones reeds section, unbalanced drone reeds are a major cause of difficulty when it comes to tuning drones. Checking their balance should part of a regular maintenance schedule. The reeds should be set-up so that if you vary your blowing pressure, the drones stay in tune to themselves, even if the overall pitch varies a little. The following method is useful for balancing or matching drone reeds and assumes that at least one tenor is correctly set up with regard to strength and pitch.
  • Firstly plug the chanter stock.
  • While blowing slightly under your average pressure, stop your bass drone and tune the tenors.
  • Once you have done this, increase your blowing to slightly above your average pressure. If the drones stay in tune to themselves, then they are matched. If the sound begins to waver, this means one drone is less stable than the other.
  • If this happens, hold the increased pressure and re-tune the drones by locating the one you have to lengthen. This is the least stable drone as it has reacted the most to the change in pressure. Refer to your reed's instructions to increase the stability of a reed. Generally you will either shorten the tongue and or strengthen the spring of the tongue.
  • Once the tenors are matched - bring in the bass drone and repeat the above steps with one or both tenors operating.
  • While it is important for the three drones to be balanced - they do not have to be perfectly matched over a wide range of blowing pressure - just a little below and a little above your average pressure is enough.

Ross Bates
0411 168 146

rabates1@live.com

ABN: 24 591 526 576

Website created and maintained by Ross Bates

Last updated 11/11/2026

Copyright © 2005 - 2026 Ross Bates