CHANTER TUNING GUIDE
- Shortening the
distance between
the reed and the top of the holes will raise the pitch. This is
known as "sinking the reed".
-
Lengthening
the distance between the reed
and
the top of the holes will lower the pitch. This is known as
"lifting the reed".
METHODS OF TUNING
Unlike many reeded
instruments, bagpipe reeds are not played directly in the mouth, which
means
we have no means of directly influencing the pitch of individual
notes via pressure or embouchure. While an increase or decrease in
pressure will affect the general pitch of the chanter, it is
certainly not a practical method of tuning. The
tuning of the chanter depends on reed manipulation and
adjusting hole size - either by using tape or undercutting holes.
TAPE
- Chanters
are best tuned with tape covering 1mm to 2mm of the top of each hole.
Some will consider this excessive and granted, in a
stable environment, with a well matched reed and chanter, it is
possible to have a well set scale with minimal use of tape. But
in the real world, especially when playing outdoors, having tape on
every note is of great advantage when trying to compensate for the
effects
of temperature change. The problem with the pipe chanter is that when
the
temperature changes, the tuning of the chanter will also
change, but not evenly throughout the scale. Moisture on the
reed will also alter some notes more than it will others.
- Due
to this uneven pitch change, we need to have a method of tuning each note
independently, and this is where tape comes in. Don't believe in the
myth that every note taped equates to having a poor quality
chanter or reed. It is a practical method of creating an accurate scale and not one that is just near enough. Don't use
normal cello tape, but use black electrical tape or one of the specialty chanter tapes on the market.
- It should
be stressed that tape is for fine-tuning. If you end up
with a note half
covered with tape, then you have a reed and or chanter issue that
needs to be
addressed.
- The application of
tape over the
top of a hole will lower its pitch. This is because you have
increased the distance between the reed and the top of the hole,
which is effectively now tape.
-
If you then move the
tape to a
higher position, the notes pitch will be sharpened. This is because
you have decreased the distance between the reed and the top of the
hole.
TAPE
&
TEMPERATURE INCREASE
-
Temperature
increase will lift
the pitch of your chanter, with the lower notes being the most affected. To re-balance the chanter, you could remove
some tape from the top notes, or sink the reed. The problem with
these methods is that your overall pitch could end up significantly
higher. A more convenient method is to apply additional tape to the
bottom notes - Low G, Low A, B and possibly C. The advantage is that your overall
pitch will not go up as much, and when the temperature decreases, you
can replace the tape to its higher position.
TAPE
&
TEMPERATURE DECREASE
- Temperature
decrease will lower the pitch of your
chanter, again with the lower notes being the most affected. To
re-balance the chanter,
you could apply more tape to the higher notes, or lift the reed. Both
of these methods could significantly lower your pitch. The easier
method is to sharpen the lower notes by lifting some tape to
compensate. Again, these will be Low G, LOw A, B and possibly C. Your
overall pitch will not go down as much and you can replace the tape to
its lower position
when the temperature
increases.
- If a note is persistently flat with
a variety of reeds, and it has little or no tape compared to the rest
of the scale, undercutting the top of the inside of the hole will
permanently sharpen its pitch and bring it into line with the other
notes on the chanter. This should only be done when you are
absolutely certain that a note is flat and out of balance with the
rest of the scale. If you have any doubt at all, do nothing and
further adjust the reed or seek advise.
-
If you are
confident enough to go
ahead, undercutting can be done with a thin hobby knife or a thin file.
Only remove a small amount of material at a
time and then test.
-
Undercutting
alone will only
sharpen a note so much and in some cases, pipers will actually
enlarge the hole opening by cutting its top end at a 90 degree
angle to the outside edge of the chanter. From here, further
undercutting can be done if required. While this is not uncommon in
top level bands, you should perhaps look to
further adjusting the reed or changing chanters if you still have
problems.
- To begin with, place
approximately 1mm of tape over the top edge of each hole - including
the Low G sound holes. This will slightly lower the overall pitch and
give
you the opportunity to raise or further lower the pitch of individual
notes as
required. Any more than 2mm of tape on any given hole
would normally be considered excessive.
- The
next step is to
position the
reed in the chanter's reed seat with about two thirds of the staple or
tie
on thread showing. This will give you a good starting point from
where you may have to lift or sink the reed if necessary. It should
be noted that it is desirable to set up a chanter with the reed as
high as possible in the chanter's reed seat. This will help to create
a stable, full sounding top hand, and help to reduce excessive crow on
High A.
TUNING A TENOR DRONE TO LOW A
- Plug
your bass drone and one of the tenors.
- Ignoring High A and
the rest of
the scale, play Low A and listen to its tuning relative to the
drone. It is likely that you will hear some wavering. You will
need to experiment with moving the the tenor in the direction
required to slow the wavering down.
- While moving the
tenor, play High
A with the left hand and periodically check your Low A. If the
wavering speeds up, move the drone in the other direction until it
slows down and eventually stops. At this point, the drone and Low A
will be in
tune.
- Despite
the fact
that your Low A
is taped and therefore tunable, from here on in, do not adjust it. Low
A will be your reference for the rest of the tuning
procedure. Once your chanter is tuned however, you may find that if
your environment changes, a slight alteration to the tape on the lower
notes is all that will be required to correct
your scale relative to the drones.
- As you proceed, regularly check
your Low A against the
drone and
retune as required. This is particularly important in the first 10
minutes or so, as the chanter will rise in pitch as the reed warms up.
CHECKING THE BALANCE OF HIGH A & LOW A
- With the drone tuned
to Low A,
change to High A and listen to the tuning. Make sure you are playing
a true High A with the bottom hand on the chanter. Listen for a
unified sound. If you hear wavering, then the High A is either flat,
or sharp.
- Ignoring the
Low A, re-tune
the tenor drone so that it is in tune with High A. If you lengthened
the drone, then the High A is flat relative to the Low A. If you
shortened the drone, then the High A is sharp relative to the Low A.
- Reposition the reed
so
that the
High A and Low A are balanced, and therefore both in tune with the
drone. Lifting the reed will flatten
the High A
more than it will the
Low A, and sinking the reed will sharpen the High A more than it will
the Low A.
- If you're overall pitch is now
either too
high or too
low,
reposition the reed to compensate, and instead balance the
chanter by adjusting the tape on High A.
LEARNING WHAT TO LISTEN FOR
Before
tuning the chanter to
the
drone, it can be a good learning experience to first of all practice
tuning a drone to the various notes on the chanter. This will help
you to understand what "flat", "in tune",
and "sharp", actually mean in terms of sound.
While
it is
relatively easy hear
if High A or Low A are in tune or not, the other notes are not as
straightforward. In very simple terms, you need to listen for a chord
with the drones. If a note is out of tune with the drones, you will
hear wavering, but it will not be as pronounced as with High A and
Low A. When a note is only slightly out of tune, it will be difficult
to hear wavering at all. Instead, if the note is flat, it will sound
"dull" and "choked". If the note is sharp, it
will sound "shrill" and "harsh".
A useful
note to start
with is D, because it is possible to play D without using the bottom
hand on the chanter. (The removal of the right little finger only
raises the pitch of D very slightly). By playing D at the same time
as tuning the drone, you can learn to listen for the changing
harmonics between the two as you move the drone up and down.
- Play D, with your
bass and one
tenor plugged.
- At the same time,
move the operating
tenor up and down. You will hear the harmonic relationship between the drone
and chanter alter as the D becomes flat or sharp relative to the
drone. Remember that flat will sound dull and
sharp will sound shrill.
- Listen carefully so that you are able to hear the speed of the
wavering between chanter and drone slow down. Keep moving
the drone until the sound of the chanter and drone lock in to form a
chord. Then move the drone slightly higher - the note should sound
shrill (sharp). Then move the drone slightly lower - the note should
sound dull (flat). Then bring the drone back in tune with the D so
that the sound locks in again.
- Practice with the
other notes as
well. It will not be as convenient as with D, because you will need
to check all other notes with both hands on the chanter. The
principal is exactly the same as for D however. To make the exercise
easier, you could tape the holes closed to play the note you want to
hear - this way you can still tune the drone at the same time as
hearing the note.
TESTING THE NOTES RELATIVE TO LOW A
Now you
need to test which
notes
are sharp and which notes are flat, relative to the to Low A or
drone. If you can hear which notes are sharp or flat - you're half
way there. If you're still unsure, the following method will help.
-
Tune a tenor drone
to Low A,
making note of it's position on the pin.
- Now, tune the drone
so that the
Low G is in tune. If the drone had to be shortened, this means that
the Low G is sharp relative to the Low A. If the drone had to be
lengthened, this means that the Low G is flat relative to the Low A.
- Repeat these two
steps for the
rest of the scale, remembering to retune the drone to Low A before
checking each note. When you are finished, you will have an
indication of what your chanters characteristics are and where tape
will need to be adjusted. To make things easier, write down your
results as you proceed.
TUNING THE CHANTER
From the above test, you will know which notes are sharp and
which notes are flat relative to the Low A.
Go back to your
record of which
notes are sharp or flat. With a tenor drone tuned to Low A, adjust the
tape on each note so that they are in tune with the
drone.
NOTES
FLAT
TO THE DRONE
- Decrease the amount
of tape
covering the hole of that note. Try to ensure there is some tape left
so you still have room to move.
-
If E, F, High G, and
High A are
flat to the drone, sinking the reed will help. This will raise the
overall pitch
and most of the effect will be on the top 3 or 4 notes.
-
If D, C, and B are
flat to the
drone, sinking the reed will also help, but it might cause the higher
notes to become too sharp. Compensate by increasing the tape on the
sharp notes, or consider the possibility of undercutting the flat
notes.
-
Another alternative
is to
increase the amount of tape on Low A. This will require you to lower
the pitch of the drone, which will bring it closer to the flat
notes.
- Increase the amount
of tape
covering the hole of that note. Any more than 2 mm of tape could
signify that further adjustment is required to the reed and or chanter.
- If most of the notes
are sharp,
you could lift the reed. This will lower your overall pitch, and most
of the effect will be on the top 3 or 4 notes. You may find that this
will also make your High A too flat.
- If
you find that
your overall
pitch is now too low, adjustment to the reed may be necessary.
INDIVIDUAL
NOTES SIGNIFICANTLY OUT OF TUNE
Refer to Chanter Reeds for more
information.
TUNING 3 DRONES TO THE CHANTER
Once you are confident
that your chanter is in
tune, it
is time to operate all three drones at once and tune them to Low A. The
principals are exactly the same as for tuning the drones to themselves,
except that like the tenor drone you have been using up to this point,
all three will be tuned to Low A.
With practice, you will be
able to tune all three drones at once while
playing High A. Remember that when playing High A with only the left
hand, it is only a rough guide due to the fact it's pitch will be
slightly sharp without the bottom hand on the chanter. Another point to
be aware of is that your pipes will take more air with all three drones
operating. You may find that you will need to increase your overall
pressure to keep the chanter at the required pitch and to keep the
High A clear. It's more than likely you will need re-tune the chanter
to a small degree once all three drones are operatring. Refer to Tuning Drones for more information.
- The reed needs to be
low enough
in the reed seat so that the pitch is what you require and yet high
enough so that you don't have problems with top hand stability.
- You then need to
know whether
most of the chanters scale is sharp or flat, relative to the Low A
(Drones). Taping will lower the pitch of the sharper notes, but you
may find that if there is too much tape on some
holes
(more than 3mm),
you may have to consider the possibility of
undercutting the
flat notes to compensate.
- Ideally, there
shouldn't be any
major difference with the amount of tape on each hole. This is where
careful undercutting can help to balance up a chanter.
- When sinking or
lifting a reed
in the chanter's reed seat - all notes are changed, however the
higher notes are more sensitive and will alter more than the lower
notes.
- Lower notes are the
most unstable with temperature change. Low G, Low A, B, and to a
lesser degree C,
will sharpen more than the higher notes in the heat, and flatten more in the cold.
- As
you tune the chanter, regularly check
your Low A against the
drone, or drones, as the chanter will sharpen slightly as it is played
- particulary when the reed is cold.
- Make sure you blow with a steady pressure.
Ross Bates
0411 168 146
rabates1@live.com
ABN: 24 591 526 576
Website created and maintained by Ross Bates
Last updated 11/11/2026
Copyright © 2005 - 2026 Ross Bates
|